Instrumentation fault diagnosis ten tactics
1. Introduction of Waste Motor Oil Distillation Plant
Waste Motor Oil Distillation Plant ,is the new technology which can refine the waste motor oil into base oil(which can be made into diesel and gasoline after processed by our catalyst). The oil quality is better than the original normal pressure distillation technology, which show on purity ,transparence, lightness .this technology will do deodorization and destinke process to the raw material oil automatically by "dry type" vacuum pressure distillation method. With the vacuum distillation technology, the distillation temperature is considerably reduced, and the oil output will higher 5%-10% compared with original normal pressure distillation technology. It makes more profits to the enterprise virtually.
2. Raw material which can be used
a. Waste oil .example: waste diesel, waste oil residue etc.
b. tire/rubber oil
c. plastic oil
d. crude oil
e. waste engine oil
f. waste motor oil
g. waste lube oil
h. waste transformer oil
i. underground oil
3. Models of waste motor oil distillation plant
4. Installation: We will be in charge of arranging our engineer to go to your place to guide the installation and train your workers how to operate the waste motor oil distillation plant ,and buyer will be in charge of the food, accommodation and round air tickets.
5.Waste Motor Oil Distillation Plant Exporting Experience:
America:
Brazil, Canada, Colombia, USA,
Middle East:
Dubai, Iran, Jordan, Saudi Arabia, Turkey
Europe:
Albania , Bosnia and Herzegovina
Asia:
Afghanistan, India, Malaysia, Pakistan, Philippines, South Korea, Vietnam, Myanmar
Africa:
Ghana, Mozambique, Zambia
Waste Motor Oil Distillation Plant Waste Motor Oil Distillation Plant,Used Motor Oil Regeneration Plant,Waste Oil Recycling Diesel Plant,Diesel Oil Distillation Plant Shangqiu Sihai Energy Technology Co., Ltd , https://www.sihaienergy.com
1, knocking hand pressure method often encounters the phenomenon of good or bad operation of the instrument, this phenomenon is mostly caused by poor contact or welding. For this situation, tapping and hand pressure can be used.
The so-called "knocking" is to gently hit the board or component with a small rubber head or other knocker to see if it can cause an error or stop failure. The so-called "hand pressure" is when the fault occurs, after the power is turned off, the plugged parts and the plug and the base are again pressed firmly by hand, and if the power supply is turned on, it will eliminate the fault. If it is found that when the cabinet is normal and the beat is not normal, it is better to re-insert all the joints and try again. If you are unsuccessful, you have to find another solution.
2. The observation method uses vision, smell, and touch. In some cases, the damaged components will discolor, blistering, or burn spots; burned devices will produce some special odors; short-circuited chips will become hot; visible or unwelded areas can also be observed with the naked eye. .
3. Exclusion method The so-called exclusion method is a method of determining the cause of failure by inserting and removing some plug-in boards and devices. When the instrument returns to normal after removing a certain board or device, it indicates that the failure occurred.
4. The replacement method requires two instruments of the same type or sufficient spare parts. Replace a good spare with the same component on the faulty machine and see if the fault is eliminated.
5. The comparison method requires two instruments of the same type, and one is in normal operation. Use this method also has the necessary equipment, for example, multimeter, oscilloscope and so on. According to the nature of comparison, there are voltage comparison, waveform comparison, static impedance comparison, output comparison, and current comparison.
The specific method is: let the faulty meter and the normal meter operate under the same conditions, and then detect the signals of some points and then compare the measured two signals. If there are differences, it can be concluded that the fault is out here. This method requires maintenance personnel with considerable knowledge and skills.
6, temperature rise and fall Sometimes, the instrument work for a long time, or in the summer when the working environment temperature is higher, there will be failure, shutdown check is normal, stop for a period of time and then boot again and normal, after a while there is a failure. This phenomenon is due to the poor performance of individual ICs or components, and the high temperature characteristic parameters do not meet the requirements of the specifications. In order to find out the cause of the malfunction, the so-called cooling down method can be adopted, that is, when the fault occurs, the anhydrous alcohol is wiped with a cotton fiber at a place where the fault may occur, and the temperature is lowered to observe whether the fault is eliminated. The so-called warming is artificially raising the temperature of the environment, such as using a soldering iron near the point of doubt (note that the temperature must not rise too high to damage the normal device) to see if the fault appears.
7, riding shoulder law riding shoulder method is also called parallel law. Place a good IC chip on the chip to be inspected, or connect good components (resistance capacitors, diodes, transistors, etc.) in parallel with the components to be inspected to maintain good contact if the fault is caused by an open circuit inside the device or For poor contact and other reasons, this method can be ruled out.
8. Capacitance bypass method When a circuit produces a strange phenomenon, such as a display chaos, a capacitor bypass method can be used to determine the part of the circuit that has failed. Connect the capacitor across the power supply and ground of the IC. Connect the transistor circuit across the base input or collector output. Observe the effect on the fault. If the fault phenomenon disappears when the capacitor bypass input is inactive and its output is bypassed, a fault is identified in this stage of the circuit.
9, state adjustment method In general, before the failure is not determined, do not touch the components in the circuit, especially adjustable devices, such as potentiometers. However, if multiple reference measures are taken in advance (for example, position marks or voltage values ​​or resistance values ​​are measured before being touched), they are allowed to act if necessary. Maybe after some change, the fault will be eliminated.
10, isolation method Fault isolation method does not require the same type of equipment or spare parts for comparison, and safe and reliable. According to the fault detection flow chart, segmentation and enveloping gradually narrow down the fault search range, together with signal comparison, component exchange and other methods, the fault will generally be quickly found. (end)
